Specification of new dyes: wash-fast, metal-free, bright and yet compatible
Disulphonated acid dyes are brilliant, offer very good wet fastness properties and are metal-free. However, most disulphonated acid dyes react differently to dyeing conditions and therefore are not compatible with each other. As a result, dye formulations with multiple disulphonated acid dyes have a low reproducibility. The new Bemacid F-T dyes are optimally matched to each other and therefore offer the best dyeing reliability, while at the same time fulfilling the desireable properties mentioned above.
Acid or metal complex dyes contain sulfonic groups that have affinity to the amino end groups of the polyamide polymer or the wool. This affinity is mainly controlled by temperature, pH value and the dyeing auxiliaries used. The absorption rate at which the dyes are absorbed onto the substrate depends, among other things, on the temperature and the dye itself. Especially in dark shades not all dye molecules can be exhausted onto the fiber and remain in the dye liquor, since the number of amino end groups is limited and the sulfonic groups of the dyes themselves accumulate on the fiber surface, creating a strong negative charge.
Deviations from critical process parameters can cause differences in the exhaustion rate of individual dyes in a recipe and may lead to an unproportional shift on the dyed product, resulting in a shade change. In some cases, this incident can be compensated for with dye migration during the leveling phase in the dye process. However, the migration capacity of disulphonated acid dyes is low.

Figure 1: Exhaust behavior and compatibility of classical disulphonated acid dyes.
It is therefore even more important to apply the dyes to the fiber as simultaneously as possible.Figure 1 shows that this is not the case with trichromatic dyeings with disulphonated acid dyes. In this formulation, consisting of the classic elements Acid Yellow 79, Acid Red 249 and Acid Blue 225, it is easy to see that the red and blue dyes are already absorbed onto the fiber at lower temperatures, while the yellow component is absorbed later, causing the shade to change significantly during the dyeing process. To make matters worse, the absorption behavior of disulfonated acid dyes is sensitive to different pH values and dyeing auxiliaries, which affects the reproducibility of the shade.
Small-molecule and monosulphonated acid levelling dyes produce much more reliably reproducible and even dyeings than disulphonated acid dyes. However, articles dyed with these dyes, especially in medium to dark shades, have a low wet fastness level, which often does not meet the requirements. Selected monosulphonated metal complex dyes offer good wet fastness and good compatibility. However, such metal-containing dyes are often no longer accepted for ecological reasons and they also tend to be dull in shade, which significantly restricts the color space. Therefore there is a demand for dyes that offer good wet fastness, even in dark shades, but are metal-free, bright and also offer good reproducibility.

Figure 2: Exhaust behavior and compatibility of Bemacid F-T dyes.
During the development of Bemacid F-T dyes, special care was taken to achieve a well-balanced exhaustion behavior and to compensate for the effect of pH change or the influence of dye-affine auxiliaries. As a result, even in trichromatic dyeings, a color tone-constant color build-up was achieved with increasing temperature (Figure 2), resulting in better reproducibility and more even dyeings compared to any combination of disulfonated acid dyes. Nevertheless, Bemacid F-T dyes are very bright dyes.

Figure 3: Color space coverage of Bemacid F-T compared to MCD Metal complex dyes.
The Bemacid F-T dyes shown in Figure 3 cover a very wide range in the color space (red line), especially in comparison to dyes of a trichromatic metal complex dye (blue line). The special characteristic of disulphonated acid dyes - the exceptionally high wet fastness of the dyed articles - is of course also evident in the Bemacid F-T dyes.
Figure 4: Wash fastness without anionic after treatment.
Figure 4 shows the result of a wash fastness test according to DIN EN ISO 105-C06/C2S (60 °C) of a dyeing with Bemacid F-T without additional anionic aftertreatment. Although the light fastness of disulphonated acid dyes is not exceptionally high, the light fastnesses of the individual elements are well matched, resulting in a better overall color consistancy during exposure than, for example, with Acid Yellow 79, Acid Red 249 and Acid Blue 225 (Figure 5).

Figure 5: Comparison of light fastness.
Of course, also for Bemacid F-T dyes, the normal challenges of disulphonated dyes cannot be completely avoided. However, to the dyer new dyes are now available offer a high level of process reliability if the specifications for wet fastness, brilliance and metal-free require the use of disulphonated acid dyes.
♦ References
.
.
Please Follow us on Social Media.
![]() | ![]() | ![]() | ![]() | ![]() |




































